<
Back

John
Broskie's Guide to Tube Circuit Analysis & Design

Next
>

17 December
2007

The Brook Amplifier: An
Amplifier with Automatic Bias Control
To
help continue the topic of variable-bias power amplifiers, John Atwood
sent me a scan of a great little article on the Brook amplifier, "High-Quality
Audio Amplifier With Automatic Bias Control." I have OCR-ed the
scan and it is available by clicking on its title.

(Why OCR? First, I want the search engines to be able
to find it. PDFs filled with images of scanned pages of text are the dark
matter of the web; they are there, but you don't know it and cannot find
it. [Dark matter? Astrophysicists tell us that dark matter is of unknown
composition and that it is dark, neither emitting nor reflecting
observable electromagnetic radiation. Yet its existence is implied by its
gravitational effects on non-dark matter.] Second, I want the article to
print more cleanly, as my 51-year-old eyes do not need any more strain;
and this article deserves the paper tribute.)

Sixty years ago, this interesting and fun-to-read
article appeared in Audio Engineering magazine (the precursor of
Audio magazine). Written by J. R. Edinger, of Brook Electronics,
the article lucidly explains how the push-pull Brook amplifier uses a
dynamically shifting bias voltage to create an output-mode-shifting
amplifier. Simply put, the Brook amplifier offers two faces: a push-pull,
class-A, low-distortion, low-power amplifier, when at idle or under low
signal levels; and a lean, mean class-AB, higher-distortion, high-power
amplifier when provoked by large input signals. Now, this is the right
sort of split personality; it’s much like having a fun, obedient, and
loving dog who will turn into a fearless, frothing, flesh-tearing guard
dog only when a loathsome intruder creeps into your house late at night.

How does the Brook amplifier
work?
The best path to understanding is to read the
article. But in a nutshell, the two push-pull output tubes share a common,
small-valued cathode resistor, which is used to monitor the current flow
through both tubes. The DC amplifier's input is a cathode, not a grid; and
the cathode attaches to the single cathode resistor shared by both output
tubes. During idle and low-level input signals, the cathode resistor sees
a fairly constant voltage drop, as the class-A operation of the output
tubes means that as one tube conducts less the other conducts more by the
same amount, so the net current draw remains fairly constant.

Automatic-Bias-Circuit (A.B.C.)

But as the amplifier is asked to go beyond its class-A
range, the cathode sees a greater current conduction, which in turn
creates a larger positive voltage drop, which in turn gets amplified by
the DC amplifier, but in an inverting mode, so the DC amplifier’s output
will swing negatively, when faced with a positive input signal. The phase
inversion comes from the second stage within the DC amplifier, which
constitutes a grounded-cathode amplifier. The DC amplifier’s output is DC
coupled to the center-tap of the interstage transformer, which will relay
the downward drift in bias voltage to the output tubes. As the Brook
amplifier’s output tubes see a greater negative bias voltage at their
grids, their idle current drops, which moves the output stage out of
class-A operation into class-AB, then class-B mode, if the input signal is
large enough.

Wait a minute, if the output stage's greater conduction
causes a more negative bias voltage at the output tubes' grids, how do the
output tubes conduct more, if they are being turned off? The DC amplifier
has an internal capacitor (C27, 0.1µF) that slows the amplifier’s reaction
to input signals, limiting the amplifier frequency response to only those
frequencies below around 6Hz, the time constant that results from the
capacitor being charged through resistor R28. (In fact, a second low-pass
is located at the DC amplifier’s output, which has an even lower
transition frequency.) In other words, the DC amplifier ignores the actual
music signal and only amplifies the shifting music envelope of increased
current draw.

The next question to answer is how the shift away from
class-A increases the potential power output. The answer is intriguing,
but it must wait for a preparatory side trip to single-ended amplifiers
with shifting bias points.

Back on the Sled

What I love about the Brook amplifier is that it steers in the
opposite direction from my single-ended
sledding-bias amplifier concept, which makes perfect sense, as the
Brook amplifier is push-pull, whereas the sledding-bias arrangement was
intended for single-ended amplifiers.

Now if I had just read that last sentence, I would stop
reading and ponder on my own why push-pull amplifiers require a
completely different approach to shifting bias than single-ended
amplifiers. Two output tubes versus one? No DC current versus a
sustained magnetizing DC current through the output transformer? A balance
driver stage versus unbalanced driver stage? Or...?

As is so often the case with multiple choice questions,
the correct answer is "none of the above." The Brook amplifier goal is
optimal music playback, not increased efficiency or extended output tube
life. The amplifier runs in a relatively heavy-current class-A mode at
idle, to produce the cleanest output signal. The rich idle current moves
the 2A3/6B4G triodes into their most linear range and then enhances that
intrinsic linearity by ensuring that both triodes completely overlap each
other’s transfer curve, thereby creating a more linear sum.

Class-A operation of a push-pull amplifier requires an
idle current at least equal to half of the peak output current, whereas
class-B operation requires an idle current as close to complete cutoff as
possible. In the Brook amplifier, the class-A output is 5W (peak) and the
class-AB output is 30W (peak). As long as the power output is below 2.5
watts (peak), the automatic-bias-circuit (A.B.C.) does not alter the
negative bias voltage presented to the output tubes. Once the output
exceeds its class-A limit, the A.B.C. kicks in, reducing the negative bias
voltage, allowing the amplifier to gracefully slide into class-B mode.

The combined plate curves for
two 2A3s working in push-push under high idle current

True class-A is truly beautiful and, like so many
beautiful things, expensive. Class-A is costly in terms of efficiency,
tube longevity, and maximum power output. Since the Brook amplifier aims
at delivering a near-perfect reproduction of musical events, the limited
output power would steal from its achievement.

With the sledding-bias arrangement for a single-ended
amplifier, in expectation of a crescendo, we raised the mild trickle of
idle current to an intense torrent, allowing the amplifier to deliver more
output voltage and current into the load. The Brook amplifier, in
contrast, lowers the bias voltage (a bit after and during the crescendo),
and with it, the idle current to achieve the same end: more power. Why the
opposite approach? The single-ended amplifier, shown above, is primarily
current-limited, as is the Brook class-A push-pull amplifier, but in an
entirely different way.

The Essential and the Accidental

It is important to understand fundamental operations within each type
of amplifier, as these limitations might be strictly law-based or no more
than accidental. For example, it is essential that the class-A, push-pull
amplifier shift down into low-current class-AB mode. In contrast, it is an
accident, a happenstance, a chance event that our sledding-biased,
solid-state, single-ended amplifier runs an unusually low idle current,
which certainly is not an absolutely essential feature of all
single-ended amplifiers, although it is an essential feature of
this amplifier. The sledding-biased amplifier's goal was a
single-ended amplifier that was primarily efficient, producing no more
heat than was absolutely required. The goal might have been altogether
different, as we might have accepted an excessively high idle current, say
10A for a nominally 16W amplifier, which need only idle at 2A to achieve
it 16 watts of output power. If the goal were absolutely the most
linearity at any cost, then 10A would certainly be a move in the right
direction. Such an amplifier is primarily voltage-limited (assuming a 40V
B+ voltage). Increasing the idle current to 20A would not increase the
power output by a milliwatt, nor would halving the idle current to 5A
increase the power output.

Increasing the B+ voltage, on the other hand, would dramatically
increase the potential output power. The low B+ voltage limits the maximum
voltage swing into the 8-ohm load. This example has been a solid-state
one, but a tube-based example is also possible. In fact, with a
triode-based single-ended amplifier, decreasing an excessively high idle
current could also increase the maximum output power. How? The
zero-grid-to-cathode-voltage boundary corrals the maximum positive-going
input signal, which in turn limits the maximum symmetrical negative-going
plate-voltage swing.

"Wait a minute," you are thinking, "you might be limited by
the zero grid voltage stop sign, but my single-ended amplifier isn’t, as
it uses an interstage transformer, so grid conduction is no problem." If
only it were so. Once the grid becomes forward biased relative to its
cathode, it defines a diode with the cathode and current flows from the
cathode to the grid, causing the grid’s normally near-infinite impedance
to plummet. This nosedive in impedance is also reflected through the
interstage transformer to its primary, thereby dragging down the driver
stage. The big advantage of using the interstage transformer over using a
coupling capacitor is that the transformer’s secondary is made from
relatively low DCR wire and it will not store an altered bias voltage, as
a capacitor would. (Capacitors preserve voltage; inductors, current.
Ideally, no DC current flows through a charged capacitor and no voltage
develops across a stressed inductor.) Had a cathode follower been used to
directly drive the output tubes' grids, then the grids could be driven
easily into conduction, assuming buffed cathode followers had been
used.

Too Many Words and Not Enough
Pictures
Below is a set of plate curves for an
imaginary triode. The triode works into a 3200-ohm plate load and a 300V
B+ voltage is used. Two idle current set points are shown. The top
loadline marks the second Iq2 amount of current conduction (about 95mA).
The bottom loadline marks the first Iq1 amount of current conduction
(about 53mA).

Single-Ended AMplifier with Two Bias Points

Setting the idle current to Iq2 will lower the
distortion, but provide less output; setting to Iq1, more output, but also
more distortion. The loadline is the same, but the permissible voltage
swing into the loadline differs with the change in idle current.

A Few Words About Loadlines

Note that the loadline remained constant in the single-ended amplifier. In
a push-pull amplifier, the loadline isn’t fixed; instead, it varies with
the output tubes’ mode of operation. Lets begin with a true class-A,
push-pull amplifier, whose output tubes never completely cut off in
response to the input signal at their grids. This means that the output
transformer’s secondary is always engaged, with some current flow through
each output tube and its branch of the secondary winding. In this case, a
transformer with a winding ratio of 20:1 will reflect an 8-ohm load as
3200 ohms across the output transformer’s secondary, as the impedance
ratio equals the winding ratio squared, which in this example is 20²:1, or
400:1. Since the loadline spans both output tube plates, each triode sees
a reflected impedance of 1600 ohms.

In contrast, with a true class-B, push-pull amplifier, its output tubes
are completely cut off at idle. This means that the output transformer’s
secondary is only engaged when current flows through either output tube
and only through the conducting triode’s branch of the secondary winding.
Thus, a transformer with a nominal winding ratio of 20:1 will effectively
hold a winding ratio of 10:1 with each half of the primary to the
secondary. Thus, the transformer will reflect an 8-ohm load as 800 ohms
across the output transformer’s primary, as the loadline spans only one
output tube plate at a time.

Class-B Loadline

Where defining a loadline gets really tricky is when the amplifier’s
mode of operation is class-AB, as each triode will see a varying loadline,
whose slope is determined by the status of conduction through both halves
of the primary and the output tubes and the degree of magnetic coupling
between windings. Because the load line cannot be represented by a
straight line, the best method to analyze a transformer-coupled, push-pull
output stage is to use a composite set of plate curves.

Single 2A3 with Vp of 250v and Iq of 51 mA

Two push-pull 2A3s with Vp of 250v and Iq of 51 mA

Composite curves of two 2A3 operating in
Class-A with
Vp of 250v and Iq of 51 mA

Composite curves of two 2A3 operating in

Class-AB with Vp of 250v and Iq of 2 mA

The composite plate curves are made by subtracting one
output tube's current conduction form the other. At idle, when both tubes
conduct equally, the two currents equal and thus cancel, which places the
center of the composite curves at zero grid volts and zero current into
the load. As the output stage is driven by inverted drive signals, the
non-linear transfer curves are averaged. So one tube's greater conduction
is met with the other tube's lesser conduction, hence the straight lines
formed in the composite plate curves drawn from two output tubes operating
in pure Class-A and the wobbly curves formed by the same tubes in
Class-AB.

Making the
Transition
Class-A operation transitioning into lean
class-AB operation requires a drop in idle current. If the DC amplifier
overshoots its mark, the amplifier will enter class-C. Never a good idea
for an audio power amplifier. So some tweaking is required. For example,
let’s say that we incorporated the Brook amplifier’s bias circuit into a
new power amplifier that was meant to use EL34s. And what if the bias
circuit were trimmed so that it never completely turned off the output
tubes. Then we decide to plug in some 8417 power tubes instead. The bias
circuit would now overachieve and would shut off the 8417s, say after an
extremely loud passage, as the 8417 needs less negative bias voltage to
cut off. In other words, the auto-bias circuit must be carefully designed.
Which leads to the question, how does one implement the Brook amplifier
technique today?

First of all, it is interesting to note how, in a quite
unintended way, the downward sliding bias method has been implicit to some
small degree in all cathode-biased amplifiers and even in many internally
capacitor-coupled amplifiers. Interestingly enough, using a conventional
cathode-bias arrangement in a single-ended amplifier has the effect of
increasing the negative bias during high output, as the
“rectification-effect” that results from the triode’s greater ability to
increase in conduction rather than be turned off results in an unbalanced
current draw through the bypassed cathode resistor, with the positive
voltage across the cathode resistor swings being greater than the negative
swings, which then increases the voltage charge across the cathode
resistor’s bypass capacitor. Depending on the capacitor’s value, the
capacitor will slowly discharge, leaving an envelope of lower idle
current, which we usually do not want. But in a single-ended amplifier
with an overly rich idle current, like the one implicit in the graph
above, the lower idle current works to our advantage.

How big is the rectification effect? Not that big. With a perfect
triode, zero rectification; with a real triode, a little less than the
percentage of 2nd harmonic distortion, which makes perfect sense, as 2nd
harmonic distortion is very much a measure of the triode’s nonlinear
handling of a symmetrical input signal.

In the case of fixed-bias, the coupling capacitors can become
excessively charged by driving the grid into positively. As long as the
increased charge across the coupling capacitor is modest, the amplifier
will approximate the Brook amplifier, as its output stage will shift into
a lower idle current. The danger, of course, is that the output stage
might already be running in a lean class-AB mode and the further downward
shift in bias voltage will completely turn off the output tubes.

In other words, I believe that we tube-loving folk are lucky that our
tube-based amplifiers can often adapt themselves to a crescendo by
shifting bias points on the fly. I am convinced that this helps explain
why a 25W tube amplifiers sound about twice as powerful as a 25W
solid-state amplifiers. I also believe that this explains why 12W class-A,
push-pull tube amplifiers sound just as powerful as 25W lean class-AB
amplifiers.

(I once built up identical push-pull, EL34-based power amplifiers,
except that one was triode-connected and the other ran pentodes. Of
course, the pentode amplifier won in maximum power output. Nonetheless,
triode-connected amplifier sounded more powerful. So I had several friends
perform the same sonic evaluation, not knowing how the amplifiers
differed. After playing each amplifier for a few tracks, I asked which
amplifier sounded more powerful. Both audiophiles and normal people all
thought the triode-based amp, the one with less than half the power,
sounded more powerful. Interestingly, when I revealed that the seemingly
weaker amplifier actually put out more than twice the watts, many
listeners, maybe all of them, immediately backpedaled and pointed at the
pentode-connected amplifier as sounding more powerful. When I grilled them
on their flip-flop, the answer I heard was always the same: but it must
sound more powerful, since it puts out more watts. Amazing what docile
consumers we have become. By the way, the triode-connected amplifier also
ran a much richer idle current.)

Broskie Sliding-Bias SE
Amplifier
To transition push-pull class-A operation
into lean class-AB operation requires a drop idle current. To transition a
low-wattage, light-current single-ended amplifier into a high-wattage (for
a single-ended amplifier), high-current single-ended amplifier requires a
boost the idle current. The obvious route would be to rectify the
secondary voltage swing and reduce a negative bias by an addition -15V or
so. But what about cathode-biased single-ended amplifiers? How can these
amplifiers achieve the same goal?

The following circuit is my answer. Imagine a power
triode, say a 300B, and imagine a ridiculously high-valued cathode
resistor, say 2k. with 400V on the plate, such an amplifier would draw
about 36mA through the output tube. This is at idle and when presented
with moderate input signals.

On the other hand, when the amplifier is provoked
beyond its class-A envelope, the NPN transistor conducts, pulling down the
cathode voltage by shorting the bypass capacitor with the 240-ohm resistor
to ground. The cathode voltage falls by about 15V and the idle current
more than doubles. If you have carefully designed your single-ended output
stage, the potential power output should increase by fourfold. In this
topology, however, a bit more could reasonably be expected, as the falling
cathode voltage gives the output tube a tad more voltage to work with.

If I were not so restrained by shame, I would have
labeled this design "Turbo SE™." Fortunately, I am not that shameless.
Unfortunately, nor am I greedy enough to patent this scheme, as it works
quite well in SPICE simulations and would make the foundation of a
desirable amplifier.

Imagine a seemingly 2W (RMS) single-ended amplifier
whose output tube only dissipated 12W at idle, but could still put out 9W
(RMS); or, think big, a 10W (RMS) single-ended amplifier whose output tube
only dissipated 60W at idle, but could still put out 45W (RMS).

One aspect of this design that should always remembered
is that it is a reactive design, not a proactive one. The amplifier
responds to being overdriven, it does not anticipate the increased need,
as the sledding-bias design does. In addition, the design assumes that
interesting music will be played through it. Much like the 50W tweeter
that burns out when presented with 10W of constant sinewaves, this design
assumes that crescendos are fairly infrequent, not constant. Still, it is
a wonderful compromise that would yield long tube life and low heat, yet
could deliver some real power into your loudspeakers.

Next Time

I will have more new circuits in the next installment, but I have to give
my aching fingers a rest.

//JRB

Kit User Guide PDFs
Click
image to download

9-Pin & Octal
PCBs & Kits

High-quality, double-sided, extra thick, 2-oz traces, plated-through
holes, dual sets of resistor pads and pads for two coupling capacitors.
Stereo and mono, octal and 9-pin printed circuit boards
available.

Designed by John Broskie & Made in USA

Aikido PCBs for as little as
$20.40

http://glass-ware.stores.yahoo.net/

On
Sale Now

Only
$19.95 $16.95

to keep track of your
tube and part collection

TCJ My-Stock DB

TCJ
My-Stock DB helps
you know just what you have, what it looks like, where it is, what it will
be used for, and what it's worth. TCJ
My-Stock DB helps
you to keep track of your heap of electronic parts. More
details.

Version 2 Improvements
List all
of your parts in one DB.
Add part Images.

One-click web searches for part information.

Vertical and horizontal grids.*

Create reports as PDFs.*
Graphs added 2D/3D: pie
& bar.*
More powerful DB search.

Help system added.
Editable
drop-down lists for location, projects,
brands, styles, vendors and more.

*User definable

Download or CD ROM
Windows
95/98/Me/NT/2000/XP
For more information, please
visit:

http://www.glass-ware.com/

To
purchase , please visit our Yahoo Store:

http://store.yahoo.com/glass-ware

<
Back

www.tubecad.com

Copyright © 1999-2007
GlassWare
All
Rights Reserved

Next
>