Toggle navigation 300guitars.com

Shop

Blog

Articles

Tips

Reviews

Spotlight

E
Book

Gear for Sale

Impedance – Speaker Cabinet Wiring

Impedance – Speaker Cabinet WiringThere are a number of
important technical issues relating to the matching of speakers
to
amplifiers, and to the wiring of multiple speaker systems (eg 2 x 12″, 4 x 12″,
etc.).

Impedance – Cabinet Wiring
The impedance of a speaker is
basically a measurement of how hard the amplifier will have to work to drive
that speaker. The impedance is measured in Ohms and is marked on the back of
most speakers. The impedance of the speaker(s) installed in an amplifier or
cabinet will be quoted in the operating instructions (If you have them). It is
essential, particularly in the case of tube (valve) amplifiers that the
impedance or ‘load’ presented to the amplifier is correct; otherwise this can
damage the amplifier. Many tube amplifiers are set up with multiple ‘taps’, eg.
8 and 16 Ohms. In such cases, it is important that the impedance of the speaker
system matches the impedance value set on the amplifier. Most transistor
amplifiers are designed to drive 8 Ohm loads. Although the impedance matching is
not as critical as with tube amplifiers, the impedance of the speaker(s) should
be at least equal to the minimum impedance of the amplifier. The majority of
guitar speakers are available in a choice of 8 and 16 Ohm impedances. However,
the way in which multiple speakers are wired
(in a 4 x 12″ cabinet for
instance) determines the overall impedance of the speaker system. Hence wiring
is critical. There are basically two ways of wiring multiple speakers: Series
and Parallel.Here are diagrams of the most typical wiring configurations.

Power Rating
If multiples of identical speakers are used
in a combo or cabinet, the overall power rating is calculated by multiplying the
individual speaker rating by the number of speakers in the cab, eg: 4 x 25 watts
= 100 watts. However, when speakers are mixed, the lower rating is used to make
the calculation, as both speakers draw the same power from the amp. For example,
in the case of one 60 watt speaker and one 25 watt speaker in the same cab, the
effective power rating is calculated as follows: 1 x 25 watts + 1 x 25 watts =
50 watts total.
It is not critical to match the power handling of a speaker
system precisely with the power output of the amplifier. But as a general rule,
the power rating of the speaker(s) should be at least equal to that of the
amplifier.

Phase / Polarity
All guitar speakers have just two
connectors, one marked positive (+) and the other negative (-). If one speaker
is wired the wrong way around in a multiple speaker configuration, it will not
damage the amplifier. However, it will be ‘pushing’ when the other speakers are
‘pulling’, resulting in the cancellation of some frequencies in the overall
sound. It is therefore important that the correct
wire goes to the correct
terminal.
Credit: Extroverts Anonymous

Want more? For further in-depth information on speaker
impedance and wiring visit the Sound City page.

Let Me Repair Your Guitars & Amps

The 300Guitars Shop

Billy Penn’s 300guitars Shop located at 1L Executive Drive in Toms River, NJ
will bring your guitars and amplifiers back to life! Specializing in guitar
& amplifier repairs and restorations in New Jersey.

Guitar
Repairs

Guitar
Restoration

Guitar Amplifier
Repairs

Custom Tube Amp
Building

Guitar Pickup
Rewinding

Guitar Amplifier
Modifications

Click
here to find out more

How to find me

View
Larger Map

Address:

300Guitars Shop
1L Executive Drive

Toms River, NJ
08755
Phone: 848-218-0362

Share this post: on Twitter on Facebook on Google+









Search for: Search

Top Articles

Tube
Amplifier Crackling Noises - What to Look For | 300guitars.com

Hot-Rodding
The New Fender Champion 600! | 300guitars.com

Guitar
Tone Caps | 300guitars.com

Phase
Inverter - What it Does and How it Works | 300guitars.com

300guitars Shop |
300guitars.com

Multi-Effects
Units vs Individual Pedals | 300guitars.com

Pedalboard
Planner Website by Pedaltrain - Build a Virtual Pedalboard! |
300guitars.com

Marshall
Amplifier Date Codes | 300guitars.com

Gear for
Sale - Amplifiers, Guitars, Pedals

Amplifier
Loudness: Watts and Decibels |
300guitars.com

Recent Comments

James
Latimer on Ron
Smith Archtop Guitars

James
Latimer on Ron
Smith Archtop Guitars

Robert
Heyl on Filter
Cap Failure

Jesse
Vukas on New
Jensen P10R-F

Scott
Shannon on Checking
Speaker Impedance With a Multimeter

Archives

April 2015

January 2015

October 2014

September 2014

August 2014

July 2014

June 2014

May 2014

April 2014

March 2014

February 2014

January 2014

March 2013

February 2013

January 2013

December 2012

November 2012

October 2012

July 2012

June 2012

May 2012

April 2012

March 2012

February 2012

January 2012

December 2011

November 2011

October 2011

September 2011

August 2011

July 2011

June 2011

May 2011

April 2011

March 2011

February 2011

December 2010

November 2010

October 2010

September 2010

August 2010

July 2010

June 2010

May 2010

April 2010

March 2010

February 2010

January 2010

December 2009

November 2009

October 2009

September 2009

August 2009

July 2009

June 2009

May 2009

April 2009

March 2009

February 2009

January 2009

December 2008

November 2008

October 2008

September 2008

August 2008

July 2008

June 2008

May 2008

April 2008

March 2008

February
2008

© 2015 300guitars.com

Return
to Top ▲